- Seagate freeagent go fw usb cant initialize drive how to#
- Seagate freeagent go fw usb cant initialize drive serial number#
- Seagate freeagent go fw usb cant initialize drive Pc#
- Seagate freeagent go fw usb cant initialize drive windows#
Seagate freeagent go fw usb cant initialize drive Pc#
If you go to pc world they just look at you blank so its obvious that their is a problem they cant sort out i will give it untill the end of this month and if i am not furnished a reasonable answer i willl be demanding my mony back as their is an inherant fault and according too consumer rights i can do this as the tv does not work as advertized i really dont want too do this as i love this tv but if needs must this is the action i must take If you just want to make use of the 3TB storage then go ahead and format it with the USB-SATA adapter.I have a S ony Bravia KDL43W809CBU i purchased this tv because it was (A) Made By Sony And (B) the salesman at currys pc world assured me that you can connect a 500GB hard drive for recording tv well i have had this tv for two months now and have tried a 500GB also a 1TB harddrive but still unable to record the tv tells me the tv should be off before removing the harddrive ? but thats as far as it goes so it knows its their it just does nothing i love the tv but this is becoming a joke now i got a system firmware the other week after it finished i could see no differance The only way to recover the data is to connect directly with SATA (or find a USB-SATA bridge that doesn't mess with the sector size). The base station is solid state, and with no moving parts it is much less likely to fail than the hard drive, unless you plug in a power supply more than 12V. External hard drive has great advantage in storing a large amount of data, so a lot of people would like to buy an external hard drive with USB port in order to save a number of data conveniently.
Seagate freeagent go fw usb cant initialize drive windows#
When you connect with USB-SATA 4k sectors everything is in the wrong place so the OS says it needs to be formatted. Seagate External Drive Cannot be Detected/Recognized in PC Windows 10/8/7. The GoFlex Home's native SATA connection has a sector size of 512 byte so all the addresses in the Master File Table are based on 512byte references. They do that so that Windows XP can use a 3TB drive, otherwise Windows XP is limited to 2TB. The reason that you can't read the drive when it is connected to a laptop with a USB-SATA adapter is that most, if not all USB-SATA bridge chips change the sector size to 4096 byte.
Seagate freeagent go fw usb cant initialize drive how to#
Short answer is no I don't have any ideas how to mount the 3TB SATA Drive (removed from plastic case of a GoFlex Home NAS setup) via USB on a Laptop.ĭid you read my post at all? The GoFlex Home drive filesystem is NTFS. Number Start End Size File system Name Flagsġ 0.00TB 3.00TB 3.00TB primary msftres Delete
Sector size (logical/physical): 512B/512B Warning: The existing disk label on /dev/sda will be destroyed and all data on
We use cookies to give you the best possible experience on our website. Answered by a verified Computer technician. Okay I tried that and I was able to clear the flag but then it came back when I formatted NTFS again? Isn't that so strange? Thanks so much. My computer no longer recognizes my FreeAgent GoFlex drive on the network and I cannot find the installation CD. See this link for info on the WD format tool if you haven't already, cheers Seagate doesn't provide a similar tool for their USB adapters so they're stuck on 4096B and that's why the problems arise. WD's quick format tool interacts with their USB adapter to set the sector size (512B for factory default and 4096B for XP) so your WD drive might be set up OK. If you use the /sbin/parted /dev/sda command and then the print command and it shows a sector size of 512B then it is all good. scan -onlySeagate for just Seagate drives in a.
Seagate freeagent go fw usb cant initialize drive serial number#
Each file will use at least one cluster so larger clusters just mean you might waste a bit of disk space.Ī) you can't change it in software, it is set by the hardware andī) the physical location of data on the disk is calculated by sector. v1.2.0 1 1180 libraries improves device detection of CD-ROM and USB flash drives, support for early 90s PATA drives that dont support LBA mode, bug fix where the last digit of the SCSI Unit Serial Number was being dropped, additional logic for deferred download completion status. The default cluster size for NTFS is 4096 byte and setting a smaller cluster size is only useful if you have a lot of tiny (smaller than 4k) files. The sector size is set by the hardware and cluster size (also called allocation unit size) is set by the filesystem (software). Hi, Cluster size and Sector size aren't the same thing.